2015年8月14日星期五

Michigan Technical University in the United States for titanium standard parts cutting issues relating to the appropriate amount of cutting fluids have been studied in an attempt to meet the processing requirements of the situation, so that the least amount of cutting fluid, cutting fluid related costs are also kept to a minimum.
They test the Ford Motor Company made the concentration of cutting fluid, workpiece material, tool type and geometry are all tested and studied and analyzed the surface roughness, BUE and cutting forces , obtained by testing the most appropriate cutting fluid consumption. US manufacturing companies Thyssen "minimal lubrication" processing technology has been studied by the cutting tool flow or aerosol effect in the processing area, cutting fluid flow by the CNC program control, and achieved good results. Chengyong, who used a variety titanium standards of complex drilling minimal lubrication technology board. When drilling a titanium aluminum multilayer composite plate, friction and wear effect drilling titanium chips will lead to flared aluminum holes, the volatility and average pore diameter aperture value increases and possible tolerance. Test uses a minimal amount of lubrication technology, use coated tools and the use of swarf removal and reaming way process, reducing the width of the blade, increasing the feed horn and a stepped shaft hole machining to ensure the quality.

2015年8月6日星期四

Titanium screws, and general stainless steel, iron, titanium standard parts copper screws are the same, but the material is titanium material, usually titanium material is titanium TA2 and TC4 titanium alloy materials. Titanium screws raw materials are more expensive, titanium standards but also very beautiful to make more, it seems crafts, titanium acid corrosion, so titanium screws are generally quite high prices.

2015年8月2日星期日

If the description is made of titanium titanium titanium standard parts plate and a chemical composition of the original elements. Titanium is very light. Commonly used in aviation. Medicine. And corrosion-resistant. So the value is more expensive.
Stainless steel much cheaper. Use more widely. Why not rust stainless steel, adding more than 12.5% of chromium in the steel-related. Corruption and incompetence of corrosion in an oxidizing medium, chrome steel surface to make quickly generate a dense passive film to prevent metal matrix is destroyed. When the chromium content at more than 12.5%, form a dense stable film, rust resistance occurs leap forward consolidation, greatly enhanced corrosion resistance, which is why the amount of chromium-containing stainless steels have a 12% the above reasons. titanium standards Commonly used stainless steel 304 chemical elements like content is 1Cr18Ni9Ti where 1 means carbon. Cr18 means that the content of chromium. Ni9 Ti nickel content means that is you said above the titanium titanium plate. Rarely content in stainless steel.

2015年7月29日星期三

Titanium clad steel plate because of its excellent corrosion resistance of titanium is widely used as a variety of chemical reaction titanium bar supplier vessels, heat exchangers material, but the drawback is the high cost. In particular, when used as a structural component of the problem is particularly prominent and effective solution is to use titanium clad steel plate. Titanium and composite material called titanium steel ordinary steel composite material, both the corrosion resistance of titanium, another common plate strength as a structural material, it is important that costs are significantly reduced. In recent years, titanium clad steel plate has added a new use, which began in the field of marine civil engineering for steel titanium bar for sale structures anticorrosive material. This is not only because of its lower cost, as the main steel structure of welding installation point of view, it must titanium clad steel plate.

2015年7月25日星期六

Performance Titanium Ti: 4.507 g / cm3, Tm: 1688 ℃. Having allotrope change, ≤882.5 ℃ hcp structure of α phase, ≥882.5 ℃ body-centered cubic structure of β phase. Low strength of pure titanium, but high strength, good plasticity, low titanium tube stock temperature toughness, high corrosion resistance. Titanium has good pressure processing performance, cutting poor. Titanium heating in nitrogen combustion can occur, and therefore should be heated and welded titanium using argon. Titanium is titanium tubing classified according to the impurities, titanium into highly pure titanium (purity 99.9%) and commercially pure titanium (purity 99.5%). There are three grades of commercially pure titanium, respectively TA + sequence number 1,2,3 digital representation, the larger the number, the lower the purity.

2015年7月21日星期二

The main manufacturing process on titanium are described as follows: Forging: metal recrystallization titanium metal temperature casting process conducted above. Hot-rolled: higher recrystallization rolling processes under temperature. Cold-rolled: plastic deformation temperature is lower than the temperature of the rolling process reply. Annealing: the metal is slowly heated to a certain temperature. Then cooled at a rate to suit a metal heat treatment process. Pickling: The article was immersed in an aqueous solution of titanium wires sulfuric acid, to remove oxides and other thin-film metal surfaces. Prior to disposal or disposal center plating, enamel, rolling and other processes.

2015年7月17日星期五

Titanium surface should be smooth, in a metallic color. Titanium allows sandblasted surface supply; 2. titanium surface allowed a slight dark and local titanium bar supplier water marks, allowing local, does not exceed half of the thickness tolerance of scratches, indentations, dents and other defects, but it should be guaranteed minimum thickness; 3. titanium surface does not allow u cracking, peeling, oxide, crimping, metal and non-metallic inclusions and other macro-defect and had traces of spilled wash; 4. titanium plate titanium rod along the rolling direction clearly allow local defects, but cleared the titanium plate thickness of not less than the minimum permissible thickness; 5. special requirements on the surface quality can be agreed between suppliers.